Printer Canon Pixma Pro9500: 2 flashing orange lights

When you have two flashing orange lights with a Canon Pixmaz Pro9500, with error code 1000, 1001 or 1002, it means:


Solution 1:

·                     There is no paper (ASF).

·                     Set the paper in ASF and press "Resume/Cancel" button.

Solution 2:

·                     There is no CD or DVD tray.

·                     Set the CD or DVD tray and press "Resume/Cancel" button.

Solution 3:

·                     There is no CD or DVD.

·                     Set a CD or DVD in the CD / DVD tray, and inset the CD / DVD tray in the proper
position. Then, press the "Resume/Cancel" button.

How to fix Error 693# in Canon MX Series Printers

Description:

USB sub-system firmware error 

Resolution:

Power off the machine, and power it on again.

If the error still occurs, replace the part listed on the right (under “Parts to be replaced if the listed solutions are not effective”). 

If the above solution has not resolved your error, please contact Canon authorised service facility.

How to reset Canon Pixma IP2770

Canon PIXMAiP2770 are classified into photo printers. This printer is very suitable for use at home. Results in getting the equivalent of lab quality photos. The speed  of this printer quickly spelled out that is about 7 ipm for mono and the 4.8 ipm for color and for 4R-sized photo takes 55 seconds. Resolution of Canon PIXMA iP2770 printer at 4800 x 1200dpi (max). Still uses USB 2.0 connectivity and the type cartridge using PG-810, CL-811 (PG-810XL, CL811XL Optional). For this printer weight of 3.4 kg with dimensions of 445 X 250 X 130mm.

If a lights blink on the POWER and RESUME button alternately and it will show an error 5B00. It means that your ink absorber inside the printer is almost full. In order to solve this you need to clear or reset the counter protection of your printer. To do this, follow this steps.

First make sure that the power cable and usb cable are connected, before you perform the reset procedure. And download the resetter at the bottom of this post.

FIRST STEPS:  Entering Service Mode

You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.

2. Hold down Resume button and press Power button.

3. Keep holding down Power button and let Resume button go.

4. Then Press Resume button 5 times then let BOTH buttons go.

5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS: Using the Resetter

1. After you download the resetter, extract it and double click "servicetool.exe"

2. Press the "Main" Button, Then press "EEPROM Clear" button if a pop-up appear just click OK

5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!

Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

Canon MX700 Scanner & Windows 7 Problems

Canon released the PIXMA MX700 Office-All-In-One printer, scanner and copier in 2004, long before computer systems shipped with Windows 7. Canon does not support the MX700 with Windows 

Drivers

·         Though Canon lists the MX700 as one of the products not supported in Windows 7, the company still provides a driver and updated software for download. The same driver that worked on XP and Windows 2000 systems can function in Windows 7. Uninstall the old driver (if already installed), disconnect your printer and then install the new software.

Software

·         In addition to updating the driver, Canon has Windows 7-versions of most of the necessary and the included software for the MX700. You should be able to overcome any problems that arise from updating the operating system on your PC by installing (or reinstalling) the Canon "Solution Menu Version 1.4.3" and "My Printer Version 2.5.0."

·          

Upgrade from Vista

·         Canon reports one known error for the MX700 for users who have upgraded their operating system from Windows Vista to Windows 7. After the upgrade is complete, the MX700 scanning function appears to be disabled. Canon's recommendation is to remove all printer drivers and reinstall the MP version of the driver from the company's website.
Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

How to fix error 1313 in canon MX series Printers

Description

The paper jammed as the machine pulled in the printed paper.

Resolution

Remove the jammed paper following the procedure below -

NOTE- If the printed paper piles up on the paper output slot, the machine may pull it in and the paper jams inside the machine. Remove the printed paper from the paper output tray before it amounts to 50 sheets.

The power cannot be turned off while the machine is sending or receiving a fax, or when the received fax or the unsent faxes are stored in the machine's memory. Make sure the machine completed sending or receiving all faxes before disconnecting the power cord. If you unplug the power cord, all the faxes stored in the machine's memory are deleted.

1.      Press the [Stop] button to cancel any print jobs and turn off the machine.

2.      Detach the rear cover.

3.      Detach the transport unit cover.

4.      Pull out the paper slowly. 
NOTE - Do not touch the inner parts of the machine. If you cannot pull out the paper, open the paper output tray.

5.      Attach the transport unit cover.

6.      Attach the rear cover. 

If you were not able to remove the paper in step 4 continue below:

7.      Detach the lower and upper cassettes.

8.      Pull out the paper slowly.

9.      If the paper is not loaded properly in the cassette, remove the paper, and then reload it after aligning the edges of the sheets. 
NOTE - When reloading the paper, confirm that you are using the paper suited for printing and are loading it correctly.

10.  Attach the cassettes to the machine, and then press the [OK] button.

If the above solution has not resolved your error, please contact your nearest Canon authorised service facilit

How to Fix Error U053 and 1405 in Canon MX Series Printers

1405/ U053 - Orange light blinking 5 times

Description:

Faulty data of the print head.

Resolution:

Fixing the Canon ‘Check ink U051, U052, U053 or U059′ Error Message

Your Canon printer will the ‘Check ink U051, U052, U053 or U059′ code when it is having trouble recognising either one of the ink cartridges installed. The official Canon description for these errors is either “The FINE cartridge is not installed”, ”The FINE cartridge is not installed properly” or  “Appropriate FINE cartridge is not installed”. A FINE cartridge is any modern Canon cartridge produced that has a printhead built into the bottom of the cartridge. Whilst only Canon originals carry the ‘FINE’ branding any functioning compatible, remanufactured or refilled cartridge can be used to resolve these errors.

How do I clear the U051, U052, U053 or U059 error message?

As described above these codes can appear for a couple of reasons. “The FINE cartridge is not installed” indicates that your printer cannot recognise one or more of the installed cartridges at all and “Appropriate FINE cartridge is not installed”, would indicate that an incorrect cartridge is installed. To resolve any of these Canon error messages please follow the steps below until the message disappears:

·        Open up your printer and ensure that both the black and the colour ink cartridge are installed. Your Canon printer needs both of these cartridges installed to print, even if you are only planing on printing in black. For more information on why this is necessary click here.

·        Check to make sure your cartridges carry the correct codes. The label of the cartridge should carry codes matching or at least similar to PG-37, PG-40, PG-50, PG-510, PG-512, PG-540 or PG-540XL for the black and CL-38, CL-41, CL-51, CL-511, CL-513, CL-541 or CL-541XL for the colour. Which of these codes is correct for your printer will depend entirely upon the model of the machine. If there is no indication on the printer as to which cartridges are needed please check your user manual for confirmation.

Check the cartridges contacts are clean and un-obscured. Your Canon printer uses a series of metallic contacts on the front of the cartridge to communicate with it when installed. If these contacts are dirty or covered by protective strips etc. then your printer will not be able to use the cartridge. I recommend removing the cartridge from your printer and wiping down the contacts with a piece of kitchen tissue (or another non-fibrous tissue) to ensure no dirt, ink or natural oils are preventing your printer from reading the cartridge. When finished your cartridges contacts should appear as below.